Monoprice 3003 Wall Mount Bracket Manuel d'utilisateur télécharger pdf

FIX TO WALL

FIT SCREEN

2.MOUNT THE TV RAILS TO THE BACK OF YOUR FLAT PANEL TV: Make sure the TV Rails (b and c) are mounted

at an equal distance from the top of the TV and as close to the center as possible as shown in diagram 2-A. Safety screws

should face the outside of the television. M4, M5, M6 and M8 bolts are provided. Plastic Spacers (l) are provided for use with

M4, M5, M6 and M8 TV mount bolts on TV's with curved or recessed back panels as shown in diagram 2-B. If you are

mounting to a television with a flat back you will not need a plastic spacer as shown in diagram 2-C. Make sure these bolts

are right! Some televisions have shallow threaded inserts; we have provided 4 extra washers you may use to offset this if the

provided bolts are too long. Tighten the wind nuts on both TV Rails so that the mechanism does not move during installation.

a b

c d

e f

Wall Plate

Left TV Rail

Right TV Rail

x1 x12

M4/M5/M6

Washer

8mmLag Bolt

Concrete Anchor

x6 x6

M4x30mm

Machine Screw

M5/M6/M8

Washer

Plastic spacer

M8x25mm

Machine Screw

x10

x4 x4

M8x40mm

Machine Screw

M5x30mm

Machine Screw

M6x30mm

Machine Screw

ASSEMBLY INSTRUCTIONS

FOR ADJUSTABLE FLAT PANEL WALL MOUNT

ADJUST

TV Rail

2-B

2-C

TV Rail

Tighten

on TV

Rails

wind

nuts

Level with Top

Close to centered

2-A

TV Mounting

Hole

k or d

TV Mounting Hole

k or d

4-A

4-B

Please check whether screws are fixed well each two months.

IF YOU HAVE ANY DOUBTS REGARDING INSTALLATION CONSULT YOUR SPECIAL

FRANCHISER.

TENDING INSTRUCTION

This product is designed to mount flat panel televisions weighing up to 75kgs to a vertical firm wall.

Safety Warning: Be careful to make sure there are no missing or defective parts. Never use defective parts.

Improper installation may cause damage or serious injury.

Note: The included hardware is for mounting on walls. If you are uncertain about the nature of your wall, consult an

expert. Please consult your hardware or installation professional for proper mounting to other types or walls. The

supplied hardware is not for steel.

Forbidden Instruction: Do not mount onto plasterboard or paneled walls.

SUPPLIED PARTS: Supplied joint parts are exclusive for using in this product.

Other joint parts are forbidden to use on this product. If any parts are missing or

faulty, telephone the special franchiser for a placement.

1a.SOLID BRICK AND CONCRETE BLOCK MOUNTING: Use the Wall Plate (a) as a template to mark 6 holes

locations on the wall. The outer holes must fall to outside of the two large holes in the middle of the plate. Three in

the top row slots and three more in the bottom row. Make sure these holes are level and there is at least 200mm

between any two holes. Pre-drill these holes with a 10mm masonry bit to at least 90mm in depth. Insert a Concrete

Anchor (f) into each of these holes. Attach the Wall Plate to the wall using 6 Lag Bolts (e) and 6 M4 / M5 / M6

Washers (d).

3. HANG THE TV ONTO THE WALL PLATE:

First hook the TV Rails (b and c) over the top of the Wall

Plate (a) as showed in diagram 3-A.

Then tighten the Safety Screws as showed in diagram 3-B.

You can free to adjust your panel TV down to 15 degrees: first

loosen one wind nut, second loosen the other wind nut and

then adjust the TV which degree you want, finally tighten the

two wind nuts.

Diagram 4-A: Front view of the adjustable plasma

mount assembled

Diagram 4-B: Safety screws tightened.

Note: This product should be mounted to solid brick, concrete or hard wood

batten/studs wall.

Wall

3-A

3-B

Loosen wind

nuts on TV

Rails

Wall

Diagram 1-A

Diagram 1-B

1b.HARD WOOD WALL MOUNTING: The Wall Plate (a) MUST to be mounted to two wood studs. Use a high quality

stud sensor to locate three adjacent studs. It is a good idea to verify where the studs are located with an awl or thin nail

shown in diagram 1-A. Pre-drill a 80mm deep hole at the desired height in each stud using a 6mm drill bit. Use the Wall

Plate as a template to mark the location of the second hole in each stud. Attach the Wall Plate to the wall using the 4 Lag

Bolts (e) and 4 M4 / M5 / M6 Washers (d). Make sure the Wall Plate is oriented so the flat surface in the center of the

plate in against the wall shown in diagram 1-B.

Note: Do not use any concrete ancher when you mount the bracket onto hard wood wall.

ASSEMBLY INSTRUCTIONS 1

Résumé du contenu

Page 1 - ASSEMBLY INSTRUCTIONS

FIX TO WALLFIT SCREEN2.MOUNT THE TV RAILS TO THE BACK OF YOUR FLAT PANEL TV: Make sure the TV Rails (b and c) are mounted at an equal distance fr

Commentaires sur ces manuels

Pas de commentaire

Monoprice 3003 Wall Mount Bracket Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour la télévision Monoprice 3003 Wall Mount Bracket. Monoprice 3003 Wall Mount Bracket User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour la télévision Monoprice 3003 Wall Mount Bracket