Monoprice 6434 Wall Mount Bracket Manuel d'utilisateur télécharger pdf

This product is designed to mount flat panel televisions weighing up to 65kg/143lbs to a vertical firm wall.

Safety Warning: Be careful to make sure there are no missing or defective parts. Never use defective parts. Improper

installation may cause damage or serious injury.

Note: The included hardware is for mounting on walls . If you are uncertain about the nature of your wall, consult an

expert. Please consult your hardware or installation professional for proper mounting to other types or walls. The

supplied hardware is not for steel.

Forbidden Instruction: Do not mount onto plasterboard or panelled walls.

ASSEMBLY INSTRUCTIONS

FOR FIXED FLAT PANEL WALL MOUNT

SUPPLIED PARTS: Supplied joint parts are exclusive for using in this product. Other joint parts are forbidden to use on this product. If any parts are

missing or faulty, telephone the special franchiser for a placement.

Mounting the Wooden Wall Plate

Important! For safety, the mount must be secured to two

adjacent wood studs an least 16" apart.

1. Using a stud finder, locate and mark two adjacent studs

for securing the mount.

2. Place the wall plate against the wall and level it using the

bubble guide.

3. Make two locations (two per stud) on the wall where the

mount will be secured.

4. Remove the wall plate and drill a 80mm deep hole an each

location using a 6mm electric drill.

5. With the help of another person, replace the wall plate and fix

it to the wall using the Lag Bolts and Lag Bolt washers provided.

6. Do not over-tighten the bolts and do not release the wall plate until all screws are secure.

Mounting the Concrete Wall Plate

1. Place the wall plate against the wall and level it using the bubble guide.

2. With the help of another person, mark off four (6) locations for fixing the

mount to the wall.

3. Place the wall plate aside and drill a 90mm deep hole at each location

using a 3/8" (10mm) masonry bit. Remove any excess dust form the

holes.

4. Insert one Concrete Anchor into each hole. A hammer can

be used to lightly tap the anchors into place if necessary.

5. With the help of another person, replace the wall plate

and fix it to the wall using the Lag Bolts and Lag Bolt

Washers provided.

6. Do not over-tighten the bolts and do not release the wall

plate until all screws are secure.

Final Installation and Adjustment

1. With the help of another person, carefully lift your display and place it on the wall plate. Do not release the display until the

mounting arms have securely hooked onto the mount.

Attaching the Arms to the Display

Important! Use extra care during this part of the installation. If possible, avoid placing your display face down as it may

damage the viewing surface. Note: Your mount comes with a selection of bolt diameters and lengths to accommodate a

wide variety of display models. Note all o f the hardware in the kit will be used.

1. Determine the correct length of bolt to use with your display by first examining the back of you display.

A. If your display has a flat back, you will use one of the shorter bolts from the hardware kit.

B. If your display has a curved or recessed back, you will use one of the longer bolts along with a spacer.

2. Determine the correct diameter of bolt to use by carefully trying one bolt each from the hardware kit. Do not force any

of the bolts-if you feel resistance stop immediately and by a smaller diameter bolt.

3. Attach the arms to the back of your display using the bolts identified along with corresponding washers.

A. If you are using the M4 or M5 bolts, you will also need to use the small hole of the washers n . If you are using the M6

or M8 boles, you will also need to use the big hole of the washers n .

B. If you are using one of the longer bolts on a display with a curved recessed back, you will also use a Spacer. Use the

Small Spacer for M4 and M5 bolts and the Large Spacer for M6 and M8 bolts.

4. Make sure all screws are secure, but do not over-tighten them.

M4x30mm Screw

Big Spacer

Hardware kit

M5x30mm Screw

M6x30mm Screw

M8x25mm Screw

M8x40mm Screw

Concrete Anchor

8mm Lag Bolt

Small Spacer

Lag Bolt Washer

Washer

x4 x4

M5x10mm Screw

M4x12mm Screw

M5x12mm Screw

M6x12mm Screw

x4 x4

Diagram-1

Diagram-2

Diagram-3

Diagram-6

Diagram-5

Diagram-4

16"

ASSEMBLY INSTRUCTIONS 1

Résumé du contenu

Page 1 - ASSEMBLY INSTRUCTIONS

This product is designed to mount flat panel televisions weighing up to 65kg/143lbs to a vertical firm wall. Safety Warning: Be careful to make sure

Commentaires sur ces manuels

Pas de commentaire

Monoprice 6434 Wall Mount Bracket Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour la télévision Monoprice 6434 Wall Mount Bracket. Monoprice 6434 Wall Mount Bracket User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour la télévision Monoprice 6434 Wall Mount Bracket