a b
x1
e f
Wall Plate
8mm Lag Bolt
x6
M4x30mm
Machine Screw
h
x4
n
FIX TO WALL
FIT SCREEN
3. HANG THE TV ONTO THE WALL PLATE:
First hook the TV Rails over the top of the Wall
Plate (a). Then insert the safety bar (f) into the
gap at the bottom of the TV Rails and add a lock
as showed in diagram 4-B.
Diagram 4-A: Front view of the fixed plasma mount
assembled.
Diagram 4-B: Safety bar with a lock.
2.MOUNT THE TV RAILS TO THE BACK OF YOUR FLAT PANEL TV: Make sure the two TV Rails (b ) are mounted
at an equal distance from the top of the TV and as close to the center as possible as shown in diagram 2-A. M4, M5,
M6 and M8 bolts are provided. Plastic Spacers (i) are provided for use with M4, M5, M6 and M8 TV mount bolts on
TV's with curved or recessed back panels as shown in diagram 2-B. If you are mounting to a television with a flat back
you will not need a plastic spacer as shown in diagram 2-C. Make sure these bolts are right! Some televisions have
shallow threaded inserts; we have provided 4 extra washers you may use to offset this if the provided bolts are too long.
c d
x2
TV Rail
x4
M4/M5/M6/M8
Washer
Concrete Anchor
x6
Lag Bolt Washer
Plastic spacer
M8x25mm
Machine Screw
j
m
x4
x4
M5x30mm
Machine Screw
M6x30mm
Machine Screw
x4
x4
This product is designed to mount flat panel televisions weighing up to 75kgs to a vertical firm wall.
Safety Warning: Be careful to make sure there are no missing or defective parts. Never use defective parts.
Improper installation may cause damage or serious injury.
Note: The included hardware is for mounting on walls . If you are uncertain about the nature of your wall, consult an
expert. Please consult your hardware or installation professional for proper mounting to other types or walls. The
supplied hardware is not for steel.
Forbidden Instruction: Do not mount onto plasterboard or paneled walls.
ASSEMBLY INSTRUCTIONS
FOR FIXED FLAT PANEL WALL MOUNT
1a.SOLID BRICK AND CONCRETE BLOCK MOUNTING: Use the Wall Plate (a) as a template to mark 6 holes
locations on the wall. Three in the top row slots and three more in the bottom row. Make sure these holes are level
and there is at least 200mm between any two holes. Pre-drill these holes with a 10mm masonry bit to at least 90mm
in depth. Insert a Concrete Anchor (e) into each of these holes. Attach the Wall Plate to the wall using 6 Lag Bolts
(d) and 6 Lag Bolt Washers (h).
Diagram 1-A
Diagram 1-B
ADJUST
TV Mounting Hole
C
i
TV Mounting Hole
C
Level with Top
Close to centered
TV Rail
2-A
2-B
2-C
TV Rail
SUPPLIED PARTS: Supplied joint parts are exclusive
for using in this product. Other joint parts are forbidden
to use on this product. If any parts are missing or faulty,
telephone the special franchiser for a placement.
Please check whether screws are fixed well each two months.
IF YOU HAVE ANY DOUBTS REGARDING INSTALLATION CONSULT OUR SPECIAL
FRANCHISER.
TENDING INSTRUCTION
Note: This product should be mounted to solid brick, concrete or hard wood
batten/studs wall.
Safety bar
x1
g
i k
M8x40mm
Machine Screw
x4
1b.HARD WOOD WALL MOUNTING: The Wall Plate (a) MUST to be mounted to two wood studs. Use a high quality
stud sensor to locate three adjacent studs. It is a good idea to verify whe re the studs are located with an awl or thin nail
shown in diagram 1-A. Pre-drill a 80mm deep hole at the desired heig ht in each stud using a 6mm drill bit. Use the Wall
Plate as a template to mark the location of the second hole in each stud. Attach the Wall Plate to the wall using the 4 Lag
Bolts (d) and 4 Lag Bolt Washers (h). Make sure the Wall Plate is oriented so the flat surface in the center of the plate in
against the wall shown in diagram 1-B.
Note: Do not use any concrete ancher when you mount the bracket onto hard wood wall.
x6
Wall
a
3-A
TV
b
4-A
4-B
(8 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels